APPLIANCE REPAIR NEW YORK
Sub-Zero is the epitome of style and also performance refrigeration. It isn’t simply a device, your Sub-Zero is an essential element of your perfect kitchen area. It makes good sense that you would not want to trust your refrigerator to simply any device repair work company. You want a team of Sub-Zero refrigerator repair specialists that can shield your investment while providing the premium service you are entitled to.
It Is Fixed Device Fixing is the company you need to trust with all of your Sub-Zero repair work needs. Our professionals focus on Sub-Zero solution so you can trust that we have the skills to do the job right.
HOW TO USAGE THE MISTAKE CODE TROUBLESHOOTING GUIDE
Mistake Codes suggest issues registered by certain parts. If error codes are signed up, they will certainly show up prior to temperature level analyses while in Diagnostic Setting.
KEEP IN MIND: If Mistake Codes appear with a flashing “SOLUTION” annunciator prior to initiating Diagnostic Setting, the system experienced too much compressor run condition that may or may not be connected with the Error Codes displayed
To start Diagnostic Mode, press and also hold either COLDER trick, after that push the POWER secret, then launch both keys. Now, inspect to see if Mistake Codes are present, making sure to toggle with all mistake as well as temperature level readings by pushing either COLDER vital or either WARMER key. (See Error Code Table Below).
If Mistake Codes appear during Diagnostic Mode, follow the Error Code Troubleshooting Guide on the complying with page. The left column of the troubleshooting guide notes the error codes. The information in the appropriate column discusses what tests to execute and/or what activity to require to deal with the mistake.
NOTE: If error codes are observed in diagnostic mode, a non-flashing SERVICE annunciator will certainly appear on the LCD when Diagnostic Setting finishes, indicating mistake codes are still stored. Error Codes have to be cleared from the digital control memory manually. To get rid of the non-flashing SERVICE annunciator and also the error codes, the problem has to be dealt with as well as the device has to be ON, then:.
- On a version UC-24C: Press the Fridge Freezer WARMER as well as COLDER keys for fifteen (15) seconds.
- On a version UC-24B, UC-24R, or UC-24RO: Press the Refrigerator WARMER and also COLDER tricks for fifteen (15) seconds.
Error Code Table
| CODE | INDICATION |
| 05 | Refrig. cabinet thermistor read open or shorted for 10+ seconds, or repeatedly read erratic temp’s |
| 06 | Refrig. evaporator thermistor read open or shorted for 10+ seconds, or repeatedly read erratic temp’s |
| 07 | Freezer cabinet thermistor read open or shorted for 10+ seconds, or repeatedly read erratic temp’s |
| 08 | Freezer evaporator thermistor read open or shorted for 10+ seconds, or repeatedly read erratic temp’s |
| 20 | Defrost under-heat with no voltage feedback through Gray/White wire at defrost start |
| 21 | Defrost overheat |
| 22 | No voltage feedback through Gray/White wire at defrost start |
| 23 | Defrost overheat with no voltage feedback through Gray/White wire at defrost start |
| 24 | Defrost under-heat |
| 30 | N/A |
| 40 | Excessive Freezer Compressor Run |
| 50 | Excessive Refrigerator Compressor Run |
| Error Code | CAUSE | SOLUTION |
| Error Code 11 | The refrigerator is too warm and/or the upper cabinet has been open too long | You will receive this error if your refrigerator’s upper cabinet has been open too long or if the upper cabinet is too warm. To resolve the error, disconnect the power from the unit at the circuit breaker. Leave the power off for at least one minute. Turn the power back on and keep the refrigerator door closed until the unit has reached optimal temperature. |
Error Code 05.
A. If “EE” for fridge compartment was presented and “SERVICE” flashing, examine the following:.
- Thermistor electric links and also continuity from thermistor to J5 on control panel. Reconnect/ repair.
- Resistance of thermistor– 30,000 to 33,000 ohms at 32 ° F( 0 ° C). Replace if malfunctioning. B. If “EE” for fridge area was NOT presented, trouble is intermittent thermistor mistake:.
- Door not shutting appropriately. Proper door closing issue.
- Check light switch, electrical wiring & electrical links. Fixing wiring/ links or change switch.
- Check thermistor electric connections as well as continuity at J5 on control board. Reconnect/ fixing.
- Check resistance of thermistor– 30,000 to 33,000 ohms at 32 ° F (0 ° C). Replace if malfunctioning.
C. If “EC 05” and “SOLUTION” were blinking prior to starting analysis setting, unit likewise experienced extreme compressor run problem that might or might not be associated with the “05” Mistake Code. See Mistake Code 50 Test/Actions.
