APPLIANCE REPAIR NEW YORK
Sub-Zero is the epitome of style and also performance refrigeration. It isn’t simply a device, your Sub-Zero is an essential element of your best kitchen. It makes good sense that you would not wish to trust your refrigerator to simply any type of appliance fixing business. You want a team of Sub-Zero fridge repair work professionals that can secure your investment while offering the premium solution you deserve.
It Is Fixed Home Appliance Fixing is the business you must trust with every one of your Sub-Zero repair requirements. Our specialists concentrate on Sub-Zero solution so you can trust that we have the abilities to get the job done right.
HOW TO USE THE MISTAKE CODE TROUBLESHOOTING OVERVIEW
Mistake Codes suggest problems signed up by certain elements. If error codes are registered, they will appear before temperature analyses while in Diagnostic Setting.
KEEP IN MIND: If Mistake Codes appear with a flashing “SOLUTION” annunciator before starting Diagnostic Setting, the unit experienced excessive compressor run problem that may or may not be connected with the Error Codes showed
To initiate Diagnostic Mode, press as well as hold either COLDER secret, then press the POWER key, after that release both keys. Now, inspect to see if Mistake Codes are present, making sure to toggle through all error and temperature readings by pushing either COLDER vital or either WARMER trick. (See Error Code Table Below).
If Mistake Codes show up during Diagnostic Mode, follow the Mistake Code Troubleshooting Overview on the complying with web page. The left column of the troubleshooting guide lists the mistake codes. The info in the best column describes what examinations to do and/or what activity to take to correct the error.
KEEP IN MIND: If error codes are observed in analysis setting, a non-flashing SOLUTION annunciator will certainly appear on the LCD when Diagnostic Setting finishes, suggesting mistake codes are still kept. Mistake Codes have to be removed from the electronic control memory by hand. To clear the non-flashing SOLUTION annunciator and the error codes, the trouble should be fixed as well as the unit has to be ON, then:.
- On a model UC-24C: Press the Freezer WARMER and COLDER tricks for fifteen (15) secs.
- On a design UC-24B, UC-24R, or UC-24RO: Press the Fridge WARMER as well as COLDER tricks for fifteen (15) seconds.
Error Code Table
| CODE | INDICATION |
| 05 | Refrig. cabinet thermistor read open or shorted for 10+ seconds, or repeatedly read erratic temp’s |
| 06 | Refrig. evaporator thermistor read open or shorted for 10+ seconds, or repeatedly read erratic temp’s |
| 07 | Freezer cabinet thermistor read open or shorted for 10+ seconds, or repeatedly read erratic temp’s |
| 08 | Freezer evaporator thermistor read open or shorted for 10+ seconds, or repeatedly read erratic temp’s |
| 20 | Defrost under-heat with no voltage feedback through Gray/White wire at defrost start |
| 21 | Defrost overheat |
| 22 | No voltage feedback through Gray/White wire at defrost start |
| 23 | Defrost overheat with no voltage feedback through Gray/White wire at defrost start |
| 24 | Defrost under-heat |
| 30 | N/A |
| 40 | Excessive Freezer Compressor Run |
| 50 | Excessive Refrigerator Compressor Run |
| Error Code | CAUSE | SOLUTION |
| Error Code 15 | There is an issue or fault with the sealed system. | The “sealed system” of your refrigerator is what allows it to get cold. It consists of the compressor and condenser. Troubleshooting a sealed system fault requires the assistance of an experienced technician. However, rebooting the refrigerator may solve the error. To reboot the refrigerator, turn off power to the outlet at the circuit breaker and wait a full minute. Turn power back on and allow the refrigerator to resume operation. If the error continues, contact a Sub-Zero refrigerator repair technician. |
Error Code 05.
A. If “EE” for refrigerator area was shown and also “SOLUTION” flashing, check the following:.
- Thermistor electric connections and also connection from thermistor to J5 on control board. Reconnect/ repair service.
- Resistance of thermistor– 30,000 to 33,000 ohms at 32 ° F( 0 ° C). Replace if faulty. B. If “EE” for fridge compartment was NOT showed, problem is recurring thermistor mistake:.
- Door not closing effectively. Right door closing problem.
- Inspect light switch, electrical wiring & electrical connections. Repair service circuitry/ connections or replace button.
- Check thermistor electrical links and also continuity at J5 on control board. Reconnect/ repair service.
- Check resistance of thermistor– 30,000 to 33,000 ohms at 32 ° F (0 ° C). Replace if malfunctioning.
C. If “EC 05” and also “SOLUTION” were flashing before initiating diagnostic mode, system additionally experienced too much compressor run problem that may or might not be associated with the “05” Mistake Code. See Error Code 50 Test/Actions.
