APPLIANCE REPAIR NEW YORK
Sub-Zero is the epitome of style as well as efficiency refrigeration. It isn’t just an appliance, your Sub-Zero is an essential element of your best cooking area. It makes good sense that you would not wish to trust your refrigerator to just any type of appliance fixing company. You want a team of Sub-Zero refrigerator repair work professionals that can shield your investment while providing the premium service you are worthy of.
It Is Fixed Home Appliance Repair is the company you need to trust with every one of your Sub-Zero repair service needs. Our professionals specialize in Sub-Zero service so you can rely on that we have the skills to do the job right.
HOW TO USAGE THE ERROR CODE TROUBLESHOOTING GUIDE
Mistake Codes suggest troubles registered by certain parts. If mistake codes are registered, they will certainly show up before temperature level analyses while in Diagnostic Setting.
NOTE: If Mistake Codes appear with a blinking “SERVICE” annunciator prior to launching Diagnostic Mode, the unit experienced too much compressor run condition that might or may not be connected with the Error Codes presented
To initiate Diagnostic Setting, press as well as hold either COLDER secret, then push the POWER key, then release both keys. Now, examine to see if Error Codes exist, making sure to toggle via all error and temperature level analyses by pressing either COLDER crucial or either WARMER trick. (See Mistake Code Table Below).
If Error Codes appear during Diagnostic Setting, adhere to the Error Code Troubleshooting Guide on the adhering to web page. The left column of the troubleshooting guide lists the error codes. The details in the right column describes what tests to carry out and/or what activity to require to deal with the error.
NOTE: If mistake codes are observed in analysis mode, a non-flashing SOLUTION annunciator will appear on the LCD when Diagnostic Mode ends, indicating mistake codes are still kept. Error Codes must be cleared from the electronic control memory by hand. To get rid of the non-flashing SERVICE annunciator and also the mistake codes, the trouble needs to be corrected and the system should get on, then:.
- On a model UC-24C: Press the Freezer WARMER as well as COLDER keys for fifteen (15) seconds.
- On a design UC-24B, UC-24R, or UC-24RO: Press the Fridge WARMER as well as COLDER keys for fifteen (15) secs.
Error Code Table
| CODE | INDICATION |
| 05 | Refrig. cabinet thermistor read open or shorted for 10+ seconds, or repeatedly read erratic temp’s |
| 06 | Refrig. evaporator thermistor read open or shorted for 10+ seconds, or repeatedly read erratic temp’s |
| 07 | Freezer cabinet thermistor read open or shorted for 10+ seconds, or repeatedly read erratic temp’s |
| 08 | Freezer evaporator thermistor read open or shorted for 10+ seconds, or repeatedly read erratic temp’s |
| 20 | Defrost under-heat with no voltage feedback through Gray/White wire at defrost start |
| 21 | Defrost overheat |
| 22 | No voltage feedback through Gray/White wire at defrost start |
| 23 | Defrost overheat with no voltage feedback through Gray/White wire at defrost start |
| 24 | Defrost under-heat |
| 30 | N/A |
| 40 | Excessive Freezer Compressor Run |
| 50 | Excessive Refrigerator Compressor Run |
| Error Code | CAUSE | SOLUTION |
| Error Code 20 | Defrost underheat | This error may indicate an issue with the wiring, defrost heater, defrost terminator, or refrigerator control board. If you receive this error, contact your local Sub-Zero repair service for assistance. |
Mistake Code 05.
A. If “EE” for refrigerator compartment was displayed and “SOLUTION” flashing, examine the following:.
- Thermistor electrical links and continuity from thermistor to J5 on control panel. Reconnect/ fixing.
- Resistance of thermistor– 30,000 to 33,000 ohms at 32 ° F( 0 ° C). Change if malfunctioning. B. If “EE” for refrigerator compartment was NOT showed, problem is periodic thermistor mistake:.
- Door not closing effectively. Right door closing problem.
- Inspect light switch, circuitry & electric connections. Repair work circuitry/ links or change switch.
- Check thermistor electric links as well as connection at J5 on control panel. Reconnect/ repair service.
- Inspect resistance of thermistor– 30,000 to 33,000 ohms at 32 ° F (0 ° C). Change if defective.
C. If “EC 05” as well as “SERVICE” were flashing prior to initiating analysis mode, unit additionally experienced excessive compressor run problem that may or may not be associated with the “05” Error Code. See Error Code 50 Test/Actions.
