APPLIANCE REPAIR NEW YORK
Sub-Zero is the epitome of design and also performance refrigeration. It isn’t just a device, your Sub-Zero is an essential element of your ideal cooking area. It makes good sense that you wouldn’t intend to trust your refrigerator to simply any type of home appliance fixing business. You want a group of Sub-Zero refrigerator fixing professionals that can protect your financial investment while giving the premium solution you should have.
It Is Fixed Appliance Repair is the company you ought to trust with every one of your Sub-Zero repair work needs. Our service technicians concentrate on Sub-Zero solution so you can rely on that we have the abilities to finish the job right.
HOW TO USE THE ERROR CODE TROUBLESHOOTING GUIDE
Mistake Codes indicate issues signed up by details parts. If mistake codes are registered, they will show up before temperature readings while in Diagnostic Setting.
KEEP IN MIND: If Error Codes appear with a blinking “SOLUTION” annunciator prior to starting Diagnostic Mode, the system experienced extreme compressor run problem that may or might not be related to the Mistake Codes displayed
To initiate Diagnostic Mode, press as well as hold either COLDER secret, after that push the POWER key, after that release both secrets. Currently, examine to see if Mistake Codes are present, being sure to toggle with all mistake as well as temperature analyses by pressing either COLDER key or either WARMER trick. (See Mistake Code Table Below).
If Error Codes show up throughout Diagnostic Mode, follow the Mistake Code Troubleshooting Guide on the complying with page. The left column of the troubleshooting overview provides the mistake codes. The info in the appropriate column describes what examinations to do and/or what action to require to fix the mistake.
KEEP IN MIND: If mistake codes are observed in diagnostic setting, a non-flashing SERVICE annunciator will certainly show up on the LCD when Diagnostic Mode ends, indicating mistake codes are still stored. Error Codes must be cleared from the electronic control memory by hand. To remove the non-flashing SERVICE annunciator as well as the error codes, the trouble must be fixed as well as the device has to get on, after that:.
- On a model UC-24C: Press the Fridge Freezer WARMER and also COLDER keys for fifteen (15) secs.
- On a model UC-24B, UC-24R, or UC-24RO: Press the Refrigerator WARMER as well as COLDER tricks for fifteen (15) secs.
Error Code Table
| CODE | INDICATION |
| 05 | Refrig. cabinet thermistor read open or shorted for 10+ seconds, or repeatedly read erratic temp’s |
| 06 | Refrig. evaporator thermistor read open or shorted for 10+ seconds, or repeatedly read erratic temp’s |
| 07 | Freezer cabinet thermistor read open or shorted for 10+ seconds, or repeatedly read erratic temp’s |
| 08 | Freezer evaporator thermistor read open or shorted for 10+ seconds, or repeatedly read erratic temp’s |
| 20 | Defrost under-heat with no voltage feedback through Gray/White wire at defrost start |
| 21 | Defrost overheat |
| 22 | No voltage feedback through Gray/White wire at defrost start |
| 23 | Defrost overheat with no voltage feedback through Gray/White wire at defrost start |
| 24 | Defrost under-heat |
| 30 | N/A |
| 40 | Excessive Freezer Compressor Run |
| 50 | Excessive Refrigerator Compressor Run |
| Error Code | CAUSE | SOLUTION |
| Error Code 24 | Defrost underheat | This error may indicate an issue with the wiring, defrost heater, defrost terminator, or refrigerator control board. If you receive this error, contact your local Sub-Zero repair service for assistance. |
Error Code 05.
A. If “EE” for refrigerator area was displayed as well as “SOLUTION” flashing, inspect the following:.
- Thermistor electrical connections and also connection from thermistor to J5 on control board. Reconnect/ repair service.
- Resistance of thermistor– 30,000 to 33,000 ohms at 32 ° F( 0 ° C). Change if malfunctioning. B. If “EE” for refrigerator area was NOT presented, problem is periodic thermistor mistake:.
- Door not shutting properly. Correct door closing issue.
- Inspect light button, circuitry & electric connections. Repair circuitry/ links or replace switch.
- Inspect thermistor electrical links and also connection at J5 on control panel. Reconnect/ repair service.
- Examine resistance of thermistor– 30,000 to 33,000 ohms at 32 ° F (0 ° C). Replace if faulty.
C. If “EC 05” as well as “SERVICE” were flashing before starting analysis mode, unit additionally experienced extreme compressor run problem that may or may not be connected with the “05” Mistake Code. See Error Code 50 Test/Actions.
