APPLIANCE REPAIR NEW YORK
Sub-Zero is the epitome of style and performance refrigeration. It isn’t just a device, your Sub-Zero is an essential element of your ideal kitchen area. It makes good sense that you would not want to trust your fridge to just any kind of device repair work company. You want a group of Sub-Zero fridge repair work experts that can secure your investment while offering the costs solution you are worthy of.
It Is Fixed Home Appliance Repair service is the company you must trust with all of your Sub-Zero repair needs. Our technicians focus on Sub-Zero solution so you can rely on that we have the skills to do the job right.
HOW TO USE THE ERROR CODE TROUBLESHOOTING OVERVIEW
Error Codes suggest troubles registered by particular parts. If error codes are signed up, they will show up prior to temperature readings while in Diagnostic Mode.
KEEP IN MIND: If Mistake Codes appear with a blinking “SOLUTION” annunciator before launching Diagnostic Setting, the unit experienced excessive compressor run condition that might or might not be associated with the Mistake Codes displayed
To start Diagnostic Mode, press and hold either COLDER key, then press the POWER secret, after that launch both keys. Now, inspect to see if Error Codes exist, making sure to toggle with all mistake as well as temperature readings by pushing either COLDER key or either WARMER trick. (See Mistake Code Table Below).
If Error Codes show up throughout Diagnostic Mode, follow the Error Code Troubleshooting Guide on the adhering to web page. The left column of the troubleshooting guide lists the mistake codes. The details in the appropriate column describes what examinations to perform and/or what action to require to fix the error.
KEEP IN MIND: If mistake codes are observed in analysis mode, a non-flashing SERVICE annunciator will show up on the LCD when Diagnostic Mode ends, suggesting error codes are still stored. Mistake Codes should be removed from the electronic control memory by hand. To clear the non-flashing SOLUTION annunciator and the mistake codes, the issue has to be fixed and the system should be ON, then:.
- On a version UC-24C: Press the Freezer WARMER and COLDER secrets for fifteen (15) seconds.
- On a model UC-24B, UC-24R, or UC-24RO: Press the Fridge WARMER as well as COLDER tricks for fifteen (15) secs.
Error Code Table
| CODE | INDICATION |
| 05 | Refrig. cabinet thermistor read open or shorted for 10+ seconds, or repeatedly read erratic temp’s |
| 06 | Refrig. evaporator thermistor read open or shorted for 10+ seconds, or repeatedly read erratic temp’s |
| 07 | Freezer cabinet thermistor read open or shorted for 10+ seconds, or repeatedly read erratic temp’s |
| 08 | Freezer evaporator thermistor read open or shorted for 10+ seconds, or repeatedly read erratic temp’s |
| 20 | Defrost under-heat with no voltage feedback through Gray/White wire at defrost start |
| 21 | Defrost overheat |
| 22 | No voltage feedback through Gray/White wire at defrost start |
| 23 | Defrost overheat with no voltage feedback through Gray/White wire at defrost start |
| 24 | Defrost under-heat |
| 30 | N/A |
| 40 | Excessive Freezer Compressor Run |
| 50 | Excessive Refrigerator Compressor Run |
| Error Code | CAUSE | SOLUTION |
| Error Code 50 | Freezer and/or Refrigerator Compressor is Running Excessively | This may mean that the condenser needs to be cleaned. If there are pets in the home, the condenser may need to be cleaned more often. |
Error Code 50
A. If “EE” for refrigerator compartment was displayed as well as “SERVICE” blinking, examine the following:.
- Thermistor electrical connections and continuity from thermistor to J5 on control panel. Reconnect/ repair service.
- Resistance of thermistor– 30,000 to 33,000 ohms at 32 ° F( 0 ° C). Change if malfunctioning. B. If “EE” for refrigerator area was NOT displayed, issue is intermittent thermistor mistake:.
- Door not closing effectively. Right door closing trouble.
- Check light button, electrical wiring & electrical links. Repair work circuitry/ connections or change switch.
- Inspect thermistor electrical connections and also connection at J5 on control panel. Reconnect/ repair.
- Inspect resistance of thermistor– 30,000 to 33,000 ohms at 32 ° F (0 ° C). Replace if malfunctioning.
C. If “EC 05” and “SERVICE” were blinking prior to launching analysis mode, unit additionally experienced too much compressor run problem that might or might not be connected with the “05” Error Code. See Error Code 50 Test/Actions.
