APPLIANCE REPAIR NEW YORK

Refrigerator Repair

Oven Repair

Dryer Repair

Washer Repair

MORE APPLIANCES

THERMADOR Error Code E1
Professional Ranges Models: PDR30/36/48…PRG30/36/48

ERROR CODE	DESCRIPTION	RESOLUTION
CODE E1	Turn the clock selector knob to Off Adjust the oven control by turning the selector knob slightly to the left (counter clockwise). This may stop the flashing message/beeping and clear the display window	Repair the electronic rannge control (also called clock ERC)

The control constantly monitors system criteria for control and also oven failings as well as reports a fault code when a system problem is identified. The control uses the stoves blue “on light” and oven “home heating light” to report a discovered fault code. The control will certainly remain to blink the lights in the suitable series as long as the fault exists.

Detection of a fault does not hinder the capacity of the control to continue to operate if the mistake is not vital for the designated operation. For instance: If the range door lock is faulty, the range will continue to cook because the mistake would just stop the range from self-cleaning.

HOW TO TRANSLATE CODES
When a mistake occurs, the control will blink the blue oven “on light” and heaven “heating light” sequentially to suggest the fault. The fault codes have two numbers, these numbers are interpreted by the variety of times the lights blink. The oven “on light” will blink suggesting the first number, and also the “home heating light” will flash indicating the 2nd number.

EXAMPLE:
Mistake E9 is … No Air conditioning Followers. The code is 43. The oven “on light” will certainly flash four times, then the “heating light” will flash three times, after that time out. The series will after that repeat as long as the mistake is present.

ERROR CODES FOR OVENS WITH DREEFS CONTROL
The complying with graph shows the error codes that can be presented in the Oven/Selector home window during certain stove malfunctions. A few of the error messages can be removed by doing the complying with actions:

Turn the selector handle to OFF
2.”Tweak” the oven by turning the selector knob a little to the left (counterclockwise). This might stop the blinking message/beeping and also clear the home window.
For mistakes E1, E9, E11, E12 as well as E13, the power supply going to the also have to be shut off for a little while, and also back on again.
If an error stays presented when the selector switch is OFF, and also after attempting to get rid of the screen, as received actions 2 as well as 3, shut off the power mosting likely to the stove, as well as describe the chart below to aid you find the problem.

ERROR MESSAGE	ERROR CODE NOTES	DESCRIPTION OF PROBLEM
E1	C&E	Control board problem.
E2	G&K	Cook or Clean mode runaway (temp >635 °F) Clean mode runaway (clean temp +32 °F).
E3	A&H	Open oven temperature sensor (>5000 Ω).
E4	A&H	Shorted oven temperature sensor (<5000 Ω).
E5	K&D	Control board too cold, too hot, or defective.
E6	C&J	Control board problem.
E7	A&I	Illegal temperature display. Turn off oven and try again.
E8	A&D	Control board problem.
E9	A&E	Latch switch problem.
E10	B&D	Control board problem.
E11	A&F	CT oven – latch switch problem
E12	A&E	CT ovens – latch switch problem
E13	A&C	CT ovens – latch frozen or no power to latch motor. CMT ovens – control board not converted (refer to page 3-7 for conversion data).
E14	A&E	Latch switch problem.
E15	B&D	Control board problem.

ERROR CODE NOTES	DESCRIPTION OF PROBLEM
A	Turns heat off on the failed oven only; microwave not affected.
B	Turns all heat off; microwave not affected.
C	Disables the CLEAN mode in both ovens; allows COOK and microwave.
D	Error will remain in the display until oven is repaired and powered back up. No error tones.
E	Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN.
F	Tweaking clears to “—“ for retry.
G	Clears when the oven temperature is less then the runaway temperature with the selector switch off.
H	Can be cancelled by tweaking if a good sensor is detected.
I	Cleared with a mode change.
J	Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door.
K	Turns heat and microwave off.
L	If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message.