APPLIANCE REPAIR NEW YORK

Refrigerator Repair

Oven Repair

Dryer Repair

Washer Repair

MORE APPLIANCES

THERMADOR Error Code E10
Professional Ranges Models: PDR30/36/48…PRG30/36/48

ERROR CODE	DESCRIPTION	RESOLUTION
CODE E10	Turns all heat off, micro not affected. Error will remain in display until repaired and powered up. No error tones.	Repair the electronic range control (also called clock or ERC)

The control continuously checks system parameters for control and also stove failings and also reports a mistake code when a system problem is spotted. The control makes use of the stoves blue “on light” as well as oven “heating light” to report a discovered mistake code. The control will certainly remain to blink the lights in the ideal series as long as the mistake exists.

Discovery of a mistake does not hinder the capacity of the control to continue to function if the fault is not critical for the desired operation. As an example: If the range door lock is defective, the array will certainly continue to cook since the fault would just protect against the range from self-cleaning.

HOW TO INTERPRET CODES
When a mistake occurs, the control will certainly flash heaven stove “on light” and heaven “home heating light” sequentially to suggest the mistake. The mistake codes have 2 numbers, these numbers are analyzed by the variety of times the lights flash. The oven “on light” will certainly blink indicating the very first number, as well as the “home heating light” will certainly flash indicating the second number.

EXAMPLE:
Error E9 is … No Cooling Followers. The code is 43. The stove “on light” will flash 4 times, then the “heating light” will certainly blink 3 times, then time out. The series will certainly then duplicate as long as the fault exists.

MISTAKE CODES FOR STOVES WITH DREEFS CONTROL
The complying with chart shows the mistake codes that can be presented in the Oven/Selector home window throughout specific stove breakdowns. A few of the error messages can be cleared by executing the adhering to steps:

Turn the selector knob to OFF
2.”Fine-tune” the oven by turning the selector knob a little to the left (counterclockwise). This might quit the flashing message/beeping and also clear the window.
For mistakes E1, E9, E11, E12 as well as E13, the power supply going to the even need to be turned off momentarily, as well as back on once more.
If a mistake stays shown when the selector button is OFF, and also after attempting to clear the display screen, as received steps 2 and also 3, switch off the power going to the oven, and also refer to the graph listed below to help you find the issue.

ERROR MESSAGE	ERROR CODE NOTES	DESCRIPTION OF PROBLEM
E1	C&E	Control board problem.
E2	G&K	Cook or Clean mode runaway (temp >635 °F) Clean mode runaway (clean temp +32 °F).
E3	A&H	Open oven temperature sensor (>5000 Ω).
E4	A&H	Shorted oven temperature sensor (<5000 Ω).
E5	K&D	Control board too cold, too hot, or defective.
E6	C&J	Control board problem.
E7	A&I	Illegal temperature display. Turn off oven and try again.
E8	A&D	Control board problem.
E9	A&E	Latch switch problem.
E10	B&D	Control board problem.
E11	A&F	CT oven – latch switch problem
E12	A&E	CT ovens – latch switch problem
E13	A&C	CT ovens – latch frozen or no power to latch motor. CMT ovens – control board not converted (refer to page 3-7 for conversion data).
E14	A&E	Latch switch problem.
E15	B&D	Control board problem.

ERROR CODE NOTES	DESCRIPTION OF PROBLEM
A	Turns heat off on the failed oven only; microwave not affected.
B	Turns all heat off; microwave not affected.
C	Disables the CLEAN mode in both ovens; allows COOK and microwave.
D	Error will remain in the display until oven is repaired and powered back up. No error tones.
E	Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN.
F	Tweaking clears to “—“ for retry.
G	Clears when the oven temperature is less then the runaway temperature with the selector switch off.
H	Can be cancelled by tweaking if a good sensor is detected.
I	Cleared with a mode change.
J	Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door.
K	Turns heat and microwave off.
L	If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message.