APPLIANCE REPAIR NEW YORK

Refrigerator Repair

Oven Repair

Dryer Repair

Washer Repair

MORE APPLIANCES

THERMADOR Error Code E11
Professional Ranges Models: PDR30/36/48…PRG30/36/48

ERROR CODE	DESCRIPTION	RESOLUTION
CODE E11	Turns heat off on failed oven only, micro not affected. Tweaking clears to “—” for retry. Turns heat off on failed oven only, micro not affected.	CT oven; latch switch problem

The control constantly monitors system specifications for control and stove failures as well as reports a fault code when a system trouble is found. The control uses the stoves blue “on light” and also oven “home heating light” to report a found fault code. The control will continue to blink the lights in the proper sequence as long as the fault exists.

Detection of a mistake does not prevent the capability of the control to remain to operate if the fault is not critical for the designated procedure. For example: If the array door latch is faulty, the range will certainly continue to prepare since the mistake would only protect against the range from self-cleaning.

HOW TO INTERPRET CODES
When a fault happens, the control will blink the blue oven “on light” and the Blue “heating light” sequentially to indicate the mistake. The fault codes have 2 numbers, these numbers are interpreted by the number of times the lights flash. The stove “on light” will flash indicating the very first number, and the “home heating light” will certainly blink showing the second number.

EXAMPLE:
Mistake E9 is … No Air conditioning Fans. The code is 43. The stove “on light” will blink 4 times, then the “home heating light” will certainly flash three times, after that time out. The sequence will certainly after that repeat as long as the mistake exists.

MISTAKE CODES FOR STOVES WITH DREEFS CONTROL
The adhering to chart reveals the error codes that can be presented in the Oven/Selector home window during details stove breakdowns. A few of the error messages can be removed by carrying out the adhering to steps:

Transform the selector handle to OFF
2.”Fine-tune” the stove by transforming the selector handle a little to the left (counterclockwise). This might stop the blinking message/beeping and clear the window.
For mistakes E1, E9, E11, E12 and also E13, the power supply mosting likely to the also must be switched off momentarily, and also back on once more.
If an error continues to be presented when the selector button is OFF, and after trying to remove the display screen, as received actions 2 as well as 3, shut off the power going to the oven, and refer to the chart listed below to help you locate the problem.

ERROR MESSAGE	ERROR CODE NOTES	DESCRIPTION OF PROBLEM
E1	C&E	Control board problem.
E2	G&K	Cook or Clean mode runaway (temp >635 °F) Clean mode runaway (clean temp +32 °F).
E3	A&H	Open oven temperature sensor (>5000 Ω).
E4	A&H	Shorted oven temperature sensor (<5000 Ω).
E5	K&D	Control board too cold, too hot, or defective.
E6	C&J	Control board problem.
E7	A&I	Illegal temperature display. Turn off oven and try again.
E8	A&D	Control board problem.
E9	A&E	Latch switch problem.
E10	B&D	Control board problem.
E11	A&F	CT oven – latch switch problem
E12	A&E	CT ovens – latch switch problem
E13	A&C	CT ovens – latch frozen or no power to latch motor. CMT ovens – control board not converted (refer to page 3-7 for conversion data).
E14	A&E	Latch switch problem.
E15	B&D	Control board problem.

ERROR CODE NOTES	DESCRIPTION OF PROBLEM
A	Turns heat off on the failed oven only; microwave not affected.
B	Turns all heat off; microwave not affected.
C	Disables the CLEAN mode in both ovens; allows COOK and microwave.
D	Error will remain in the display until oven is repaired and powered back up. No error tones.
E	Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN.
F	Tweaking clears to “—“ for retry.
G	Clears when the oven temperature is less then the runaway temperature with the selector switch off.
H	Can be cancelled by tweaking if a good sensor is detected.
I	Cleared with a mode change.
J	Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door.
K	Turns heat and microwave off.
L	If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message.