APPLIANCE REPAIR NEW YORK

Refrigerator Repair

Oven Repair

Dryer Repair

Washer Repair

MORE APPLIANCES

THERMADOR Error Code E12
Professional Ranges Models: PDR30/36/48…PRG30/36/48

ERROR CODE	DESCRIPTION	RESOLUTION
CODE E12	Turn the clock selector knob to Off Adjust the oven control by turning the clock selector knob slightly to the left (counter clockwise). This may stop the flashing message/beeping and clear the display window.	CT oven; latch switch problem

The control continually monitors system parameters for control and also oven failures and reports a mistake code when a system trouble is detected. The control makes use of the ovens blue “on light” as well as oven “heating light” to report a spotted mistake code. The control will certainly continue to blink the lights in the suitable series as long as the mistake exists.

Discovery of a fault does not prevent the capacity of the control to remain to function if the fault is not critical for the designated operation. For example: If the array door lock is defective, the array will certainly continue to prepare given that the fault would only avoid the variety from self-cleaning.

HOW TO TRANSLATE CODES
When a fault occurs, the control will flash the blue oven “on light” and also the Blue “heating light” sequentially to show the fault. The mistake codes have two numbers, these numbers are interpreted by the number of times the lights blink. The oven “on light” will flash showing the first number, and the “home heating light” will blink suggesting the second number.

INSTANCE:
Error E9 is … No Air conditioning Fans. The code is 43. The oven “on light” will certainly blink four times, then the “home heating light” will blink 3 times, then time out. The series will after that duplicate as long as the mistake exists.

ERROR CODES FOR OVENS WITH DREEFS CONTROL
The adhering to chart shows the mistake codes that can be shown in the Oven/Selector window during details oven malfunctions. Several of the error messages can be removed by doing the following actions:

Turn the selector handle to OFF
2.”Modify” the stove by transforming the selector handle slightly to the left (counterclockwise). This might stop the blinking message/beeping as well as clear the home window.
For mistakes E1, E9, E11, E12 and also E13, the power supply going to the also have to be switched off temporarily, as well as back on again.
If an error stays displayed when the selector button is OFF, and after trying to clear the display screen, as received steps 2 and 3, switch off the power mosting likely to the stove, as well as refer to the graph below to help you locate the trouble.

ERROR MESSAGE	ERROR CODE NOTES	DESCRIPTION OF PROBLEM
E1	C&E	Control board problem.
E2	G&K	Cook or Clean mode runaway (temp >635 °F) Clean mode runaway (clean temp +32 °F).
E3	A&H	Open oven temperature sensor (>5000 Ω).
E4	A&H	Shorted oven temperature sensor (<5000 Ω).
E5	K&D	Control board too cold, too hot, or defective.
E6	C&J	Control board problem.
E7	A&I	Illegal temperature display. Turn off oven and try again.
E8	A&D	Control board problem.
E9	A&E	Latch switch problem.
E10	B&D	Control board problem.
E11	A&F	CT oven – latch switch problem
E12	A&E	CT ovens – latch switch problem
E13	A&C	CT ovens – latch frozen or no power to latch motor. CMT ovens – control board not converted (refer to page 3-7 for conversion data).
E14	A&E	Latch switch problem.
E15	B&D	Control board problem.

ERROR CODE NOTES	DESCRIPTION OF PROBLEM
A	Turns heat off on the failed oven only; microwave not affected.
B	Turns all heat off; microwave not affected.
C	Disables the CLEAN mode in both ovens; allows COOK and microwave.
D	Error will remain in the display until oven is repaired and powered back up. No error tones.
E	Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN.
F	Tweaking clears to “—“ for retry.
G	Clears when the oven temperature is less then the runaway temperature with the selector switch off.
H	Can be cancelled by tweaking if a good sensor is detected.
I	Cleared with a mode change.
J	Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door.
K	Turns heat and microwave off.
L	If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message.