APPLIANCE REPAIR NEW YORK

Refrigerator Repair

Oven Repair

Dryer Repair

Washer Repair

MORE APPLIANCES

THERMADOR Error Code E14
Professional Ranges Models: PDR30/36/48…PRG30/36/48

ERROR CODE	DESCRIPTION	RESOLUTION
CODE E14	Turn the clock selector knob to Off Adjust the oven control by turning the clock selector knob slightly to the left (counter clockwise). This may stop the flashing message/beeping and clear the display window	Latch switch problems

The control continuously keeps track of system parameters for control as well as stove failures as well as reports a fault code when a system trouble is discovered. The control uses the ovens blue “on light” and also oven “heating light” to report a discovered fault code. The control will continue to blink the lights in the proper series as long as the fault exists.

Discovery of a fault does not prevent the capacity of the control to continue to work if the mistake is not vital for the desired procedure. As an example: If the array door latch is defective, the range will certainly remain to prepare since the mistake would only protect against the range from self-cleaning.

HOW TO ANALYZE CODES
When a fault occurs, the control will certainly flash heaven stove “on light” as well as the Blue “home heating light” sequentially to suggest the fault. The fault codes have 2 numbers, these numbers are analyzed by the variety of times the lights blink. The oven “on light” will certainly blink suggesting the first number, and also the “heating light” will blink suggesting the 2nd number.

EXAMPLE:
Error E9 is … No Air conditioning Followers. The code is 43. The stove “on light” will certainly blink 4 times, then the “home heating light” will certainly blink three times, after that pause. The series will certainly after that repeat as long as the mistake is present.

MISTAKE CODES FOR OVENS WITH DREEFS CONTROL
The adhering to graph shows the error codes that can be displayed in the Oven/Selector home window throughout details stove breakdowns. A few of the mistake messages can be removed by carrying out the complying with steps:

Transform the selector knob to OFF
2.”Fine-tune” the stove by transforming the selector handle a little to the left (counterclockwise). This may quit the blinking message/beeping as well as clear the window.
For errors E1, E9, E11, E12 and E13, the power supply mosting likely to the also must be switched off momentarily, and back on once again.
If a mistake remains shown when the selector switch is OFF, as well as after attempting to clear the display screen, as received actions 2 and also 3, switch off the power mosting likely to the oven, as well as refer to the chart listed below to help you find the problem.

ERROR MESSAGE	ERROR CODE NOTES	DESCRIPTION OF PROBLEM
E1	C&E	Control board problem.
E2	G&K	Cook or Clean mode runaway (temp >635 °F) Clean mode runaway (clean temp +32 °F).
E3	A&H	Open oven temperature sensor (>5000 Ω).
E4	A&H	Shorted oven temperature sensor (<5000 Ω).
E5	K&D	Control board too cold, too hot, or defective.
E6	C&J	Control board problem.
E7	A&I	Illegal temperature display. Turn off oven and try again.
E8	A&D	Control board problem.
E9	A&E	Latch switch problem.
E10	B&D	Control board problem.
E11	A&F	CT oven – latch switch problem
E12	A&E	CT ovens – latch switch problem
E13	A&C	CT ovens – latch frozen or no power to latch motor. CMT ovens – control board not converted (refer to page 3-7 for conversion data).
E14	A&E	Latch switch problem.
E15	B&D	Control board problem.

ERROR CODE NOTES	DESCRIPTION OF PROBLEM
A	Turns heat off on the failed oven only; microwave not affected.
B	Turns all heat off; microwave not affected.
C	Disables the CLEAN mode in both ovens; allows COOK and microwave.
D	Error will remain in the display until oven is repaired and powered back up. No error tones.
E	Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN.
F	Tweaking clears to “—“ for retry.
G	Clears when the oven temperature is less then the runaway temperature with the selector switch off.
H	Can be cancelled by tweaking if a good sensor is detected.
I	Cleared with a mode change.
J	Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door.
K	Turns heat and microwave off.
L	If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message.