APPLIANCE REPAIR NEW YORK

Refrigerator Repair

Oven Repair

Dryer Repair

Washer Repair

MORE APPLIANCES

THERMADOR Error Code E2
Professional Ranges Models: PDR30/36/48…PRG30/36/48

ERROR CODE	DESCRIPTION	RESOLUTION
CODE E2	Turns all heat and micro off. Clears when oven temp drops below runaway temp and selector is off.	Repair the electronic rannge control (also called clock ERC)

The control constantly keeps track of system criteria for control as well as oven failures and also reports a mistake code when a system issue is detected. The control makes use of the ovens blue “on light” and also oven “home heating light” to report a discovered mistake code. The control will certainly remain to flash the lights in the ideal series as long as the mistake exists.

Detection of a fault does not impede the capability of the control to continue to work if the mistake is not essential for the designated procedure. For example: If the variety door lock is faulty, the array will remain to cook considering that the fault would just prevent the array from self-cleaning.

HOW TO INTERPRET CODES
When a fault takes place, the control will certainly blink heaven stove “on light” as well as heaven “heating light” sequentially to show the mistake. The fault codes have two numbers, these numbers are interpreted by the number of times the lights blink. The oven “on light” will flash suggesting the first number, and the “home heating light” will certainly blink suggesting the 2nd number.

EXAMPLE:
Mistake E9 is … No Air conditioning Followers. The code is 43. The stove “on light” will flash four times, then the “heating light” will certainly flash three times, after that time out. The series will after that duplicate as long as the fault exists.

ERROR CODES FOR OVENS WITH DREEFS CONTROL
The complying with chart reveals the error codes that can be presented in the Oven/Selector home window throughout particular oven malfunctions. Some of the mistake messages can be gotten rid of by doing the following steps:

Transform the selector knob to OFF
2.”Fine-tune” the stove by transforming the selector handle somewhat to the left (counterclockwise). This may quit the flashing message/beeping and clear the home window.
For mistakes E1, E9, E11, E12 as well as E13, the power supply going to the even need to be turned off briefly, and back on once again.
If an error stays presented when the selector switch is OFF, and also after attempting to clear the display, as displayed in steps 2 and also 3, switch off the power going to the stove, as well as refer to the graph below to help you find the problem.

ERROR MESSAGE	ERROR CODE NOTES	DESCRIPTION OF PROBLEM
E1	C&E	Control board problem.
E2	G&K	Cook or Clean mode runaway (temp >635 °F) Clean mode runaway (clean temp +32 °F).
E3	A&H	Open oven temperature sensor (>5000 Ω).
E4	A&H	Shorted oven temperature sensor (<5000 Ω).
E5	K&D	Control board too cold, too hot, or defective.
E6	C&J	Control board problem.
E7	A&I	Illegal temperature display. Turn off oven and try again.
E8	A&D	Control board problem.
E9	A&E	Latch switch problem.
E10	B&D	Control board problem.
E11	A&F	CT oven – latch switch problem
E12	A&E	CT ovens – latch switch problem
E13	A&C	CT ovens – latch frozen or no power to latch motor. CMT ovens – control board not converted (refer to page 3-7 for conversion data).
E14	A&E	Latch switch problem.
E15	B&D	Control board problem.

ERROR CODE NOTES	DESCRIPTION OF PROBLEM
A	Turns heat off on the failed oven only; microwave not affected.
B	Turns all heat off; microwave not affected.
C	Disables the CLEAN mode in both ovens; allows COOK and microwave.
D	Error will remain in the display until oven is repaired and powered back up. No error tones.
E	Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN.
F	Tweaking clears to “—“ for retry.
G	Clears when the oven temperature is less then the runaway temperature with the selector switch off.
H	Can be cancelled by tweaking if a good sensor is detected.
I	Cleared with a mode change.
J	Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door.
K	Turns heat and microwave off.
L	If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message.