APPLIANCE REPAIR NEW YORK

Refrigerator Repair

Oven Repair

Dryer Repair

Washer Repair

MORE APPLIANCES

THERMADOR Error Code E3
Professional Ranges Models: PDR30/36/48…PRG30/36/48

ERROR CODE	DESCRIPTION	RESOLUTION
CODE E3	Turns heat off on failed oven only, micro not affected. Can be cancelled by tweaking if a good oven temperature sensor is detected.	Open oven temperature sensor (over 5000 ohms)

The control continually checks system parameters for control and also oven failures as well as reports a mistake code when a system issue is discovered. The control uses the ovens blue “on light” and also oven “heating light” to report a found fault code. The control will remain to flash the lights in the proper sequence as long as the mistake exists.

Discovery of a mistake does not impede the capacity of the control to continue to operate if the fault is not vital for the designated procedure. For instance: If the array door lock is defective, the array will continue to cook given that the mistake would only stop the array from self-cleaning.

HOW TO ANALYZE CODES
When a mistake happens, the control will certainly flash the blue stove “on light” and heaven “home heating light” sequentially to show the mistake. The fault codes have 2 numbers, these numbers are translated by the variety of times the lights flash. The oven “on light” will blink indicating the very first number, as well as the “heating light” will certainly blink indicating the second number.

EXAMPLE:
Mistake E9 is … No Cooling Fans. The code is 43. The stove “on light” will certainly blink 4 times, after that the “home heating light” will flash 3 times, then time out. The sequence will certainly then duplicate as long as the fault exists.

ERROR CODES FOR STOVES WITH DREEFS CONTROL
The adhering to graph reveals the error codes that can be shown in the Oven/Selector home window throughout details stove breakdowns. Some of the error messages can be cleared by executing the adhering to steps:

Transform the selector handle to OFF
2.”Modify” the oven by turning the selector handle slightly to the left (counterclockwise). This may stop the blinking message/beeping and clear the window.
For errors E1, E9, E11, E12 and E13, the power supply going to the even have to be switched off for a short while, and back on once again.
If an error remains displayed when the selector button is OFF, and after attempting to clear the display, as shown in steps 2 as well as 3, switch off the power mosting likely to the stove, and refer to the graph below to aid you find the issue.

ERROR MESSAGE	ERROR CODE NOTES	DESCRIPTION OF PROBLEM
E1	C&E	Control board problem.
E2	G&K	Cook or Clean mode runaway (temp >635 °F) Clean mode runaway (clean temp +32 °F).
E3	A&H	Open oven temperature sensor (>5000 Ω).
E4	A&H	Shorted oven temperature sensor (<5000 Ω).
E5	K&D	Control board too cold, too hot, or defective.
E6	C&J	Control board problem.
E7	A&I	Illegal temperature display. Turn off oven and try again.
E8	A&D	Control board problem.
E9	A&E	Latch switch problem.
E10	B&D	Control board problem.
E11	A&F	CT oven – latch switch problem
E12	A&E	CT ovens – latch switch problem
E13	A&C	CT ovens – latch frozen or no power to latch motor. CMT ovens – control board not converted (refer to page 3-7 for conversion data).
E14	A&E	Latch switch problem.
E15	B&D	Control board problem.

ERROR CODE NOTES	DESCRIPTION OF PROBLEM
A	Turns heat off on the failed oven only; microwave not affected.
B	Turns all heat off; microwave not affected.
C	Disables the CLEAN mode in both ovens; allows COOK and microwave.
D	Error will remain in the display until oven is repaired and powered back up. No error tones.
E	Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN.
F	Tweaking clears to “—“ for retry.
G	Clears when the oven temperature is less then the runaway temperature with the selector switch off.
H	Can be cancelled by tweaking if a good sensor is detected.
I	Cleared with a mode change.
J	Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door.
K	Turns heat and microwave off.
L	If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message.