APPLIANCE REPAIR NEW YORK

Refrigerator Repair

Oven Repair

Dryer Repair

Washer Repair

MORE APPLIANCES

THERMADOR Error Code E4
Professional Ranges Models: PDR30/36/48…PRG30/36/48

ERROR CODE	DESCRIPTION	RESOLUTION
CODE E4	Turns heat off on failed oven only, micro not affected. Can be cancelled by tweaking if a good oven temperature sensor is detected.	Shorted oven temperature sensor (under 500 ohms)

The control continuously monitors system criteria for control as well as oven failings as well as reports a mistake code when a system trouble is discovered. The control utilizes the stoves blue “on light” as well as oven “heating light” to report a spotted mistake code. The control will certainly continue to blink the lights in the proper sequence as long as the mistake exists.

Detection of a fault does not prevent the capability of the control to continue to operate if the mistake is not essential for the designated procedure. For example: If the variety door latch is defective, the range will certainly remain to cook because the fault would just protect against the range from self-cleaning.

HOW TO ANALYZE CODES
When a mistake takes place, the control will flash the blue oven “on light” and also heaven “home heating light” sequentially to show the mistake. The fault codes have 2 numbers, these numbers are analyzed by the number of times the lights flash. The stove “on light” will blink indicating the very first number, and the “heating light” will certainly flash suggesting the 2nd number.

INSTANCE:
Error E9 is … No Air conditioning Followers. The code is 43. The stove “on light” will certainly blink four times, then the “heating light” will blink three times, then time out. The sequence will certainly then repeat as long as the mistake is present.

ERROR CODES FOR STOVES WITH DREEFS CONTROL
The following chart reveals the error codes that can be presented in the Oven/Selector home window throughout particular oven malfunctions. Some of the error messages can be cleared by executing the adhering to steps:

Transform the selector knob to OFF
2.”Modify” the oven by transforming the selector handle slightly to the left (counterclockwise). This might stop the flashing message/beeping and also clear the home window.
For mistakes E1, E9, E11, E12 as well as E13, the power supply mosting likely to the also need to be turned off temporarily, and back on again.
If an error continues to be shown when the selector switch is OFF, and after trying to clear the display screen, as displayed in actions 2 and also 3, switch off the power going to the oven, as well as describe the chart below to aid you locate the problem.

ERROR MESSAGE	ERROR CODE NOTES	DESCRIPTION OF PROBLEM
E1	C&E	Control board problem.
E2	G&K	Cook or Clean mode runaway (temp >635 °F) Clean mode runaway (clean temp +32 °F).
E3	A&H	Open oven temperature sensor (>5000 Ω).
E4	A&H	Shorted oven temperature sensor (<5000 Ω).
E5	K&D	Control board too cold, too hot, or defective.
E6	C&J	Control board problem.
E7	A&I	Illegal temperature display. Turn off oven and try again.
E8	A&D	Control board problem.
E9	A&E	Latch switch problem.
E10	B&D	Control board problem.
E11	A&F	CT oven – latch switch problem
E12	A&E	CT ovens – latch switch problem
E13	A&C	CT ovens – latch frozen or no power to latch motor. CMT ovens – control board not converted (refer to page 3-7 for conversion data).
E14	A&E	Latch switch problem.
E15	B&D	Control board problem.

ERROR CODE NOTES	DESCRIPTION OF PROBLEM
A	Turns heat off on the failed oven only; microwave not affected.
B	Turns all heat off; microwave not affected.
C	Disables the CLEAN mode in both ovens; allows COOK and microwave.
D	Error will remain in the display until oven is repaired and powered back up. No error tones.
E	Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN.
F	Tweaking clears to “—“ for retry.
G	Clears when the oven temperature is less then the runaway temperature with the selector switch off.
H	Can be cancelled by tweaking if a good sensor is detected.
I	Cleared with a mode change.
J	Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door.
K	Turns heat and microwave off.
L	If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message.