APPLIANCE REPAIR NEW YORK

Refrigerator Repair

Oven Repair

Dryer Repair

Washer Repair

MORE APPLIANCES

THERMADOR Error Code E5
Professional Ranges Models: PDR30/36/48…PRG30/36/48

ERROR CODE	DESCRIPTION	RESOLUTION
CODE E5	Turns all heat and micro off. Error will remain in display until repaired and powered up. No error tones.	Control board too cold or too hot, repair the electronic range control (also called clock or ERC)

The control continuously monitors system specifications for control and also stove failures as well as reports a mistake code when a system problem is identified. The control utilizes the ovens blue “on light” as well as oven “home heating light” to report a spotted mistake code. The control will continue to flash the lights in the suitable series as long as the fault exists.

Detection of a fault does not prevent the capacity of the control to continue to operate if the mistake is not critical for the designated procedure. For example: If the range door lock is inoperative, the variety will continue to prepare since the fault would only stop the array from self-cleaning.

HOW TO INTERPRET CODES
When a fault takes place, the control will blink the blue oven “on light” and also the Blue “heating light” sequentially to suggest the fault. The mistake codes have two numbers, these numbers are analyzed by the variety of times the lights blink. The oven “on light” will blink indicating the very first number, as well as the “heating light” will certainly flash suggesting the 2nd number.

EXAMPLE:
Error E9 is … No Air conditioning Fans. The code is 43. The oven “on light” will certainly blink four times, after that the “home heating light” will certainly flash three times, then pause. The sequence will certainly after that repeat as long as the fault is present.

ERROR CODES FOR OVENS WITH DREEFS CONTROL
The complying with graph reveals the mistake codes that can be shown in the Oven/Selector home window during particular stove malfunctions. Some of the mistake messages can be gotten rid of by doing the adhering to actions:

Turn the selector handle to OFF
2.”Modify” the oven by turning the selector handle somewhat to the left (counterclockwise). This may quit the blinking message/beeping as well as clear the window.
For mistakes E1, E9, E11, E12 and E13, the power supply going to the even have to be turned off temporarily, as well as back on once more.
If an error remains shown when the selector button is OFF, and after attempting to remove the display screen, as shown in steps 2 and 3, switch off the power mosting likely to the stove, and also describe the chart below to assist you locate the trouble.

ERROR MESSAGE	ERROR CODE NOTES	DESCRIPTION OF PROBLEM
E1	C&E	Control board problem.
E2	G&K	Cook or Clean mode runaway (temp >635 °F) Clean mode runaway (clean temp +32 °F).
E3	A&H	Open oven temperature sensor (>5000 Ω).
E4	A&H	Shorted oven temperature sensor (<5000 Ω).
E5	K&D	Control board too cold, too hot, or defective.
E6	C&J	Control board problem.
E7	A&I	Illegal temperature display. Turn off oven and try again.
E8	A&D	Control board problem.
E9	A&E	Latch switch problem.
E10	B&D	Control board problem.
E11	A&F	CT oven – latch switch problem
E12	A&E	CT ovens – latch switch problem
E13	A&C	CT ovens – latch frozen or no power to latch motor. CMT ovens – control board not converted (refer to page 3-7 for conversion data).
E14	A&E	Latch switch problem.
E15	B&D	Control board problem.

ERROR CODE NOTES	DESCRIPTION OF PROBLEM
A	Turns heat off on the failed oven only; microwave not affected.
B	Turns all heat off; microwave not affected.
C	Disables the CLEAN mode in both ovens; allows COOK and microwave.
D	Error will remain in the display until oven is repaired and powered back up. No error tones.
E	Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN.
F	Tweaking clears to “—“ for retry.
G	Clears when the oven temperature is less then the runaway temperature with the selector switch off.
H	Can be cancelled by tweaking if a good sensor is detected.
I	Cleared with a mode change.
J	Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door.
K	Turns heat and microwave off.
L	If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message.