APPLIANCE REPAIR NEW YORK

Refrigerator Repair

Oven Repair

Dryer Repair

Washer Repair

MORE APPLIANCES

THERMADOR Error Code E6
Professional Ranges Models: PDR30/36/48…PRG30/36/48

ERROR CODE	DESCRIPTION	RESOLUTION
CODE E5	Disables clean mode in both ovens, allows cook and microwave. Can be tweaked away for retry. User must unlatch and delete the “—” to try to re-latch the door.	Repair the electronic range control (also called clock or ERC)

The control constantly keeps an eye on system specifications for control and stove failings and also reports a fault code when a system trouble is identified. The control utilizes the ovens blue “on light” and oven “home heating light” to report a discovered mistake code. The control will remain to blink the lights in the ideal series as long as the fault exists.

Detection of a mistake does not hinder the capability of the control to continue to operate if the mistake is not important for the intended operation. For example: If the array door lock is inoperative, the variety will continue to cook because the mistake would just stop the range from self-cleaning.

HOW TO ANALYZE CODES
When a mistake happens, the control will certainly flash the blue stove “on light” as well as heaven “home heating light” sequentially to show the fault. The mistake codes have 2 numbers, these numbers are analyzed by the variety of times the lights blink. The oven “on light” will certainly blink showing the initial number, and the “heating light” will blink showing the 2nd number.

EXAMPLE:
Error E9 is … No Cooling Fans. The code is 43. The stove “on light” will certainly flash four times, after that the “home heating light” will certainly flash 3 times, then pause. The sequence will certainly then duplicate as long as the mistake exists.

MISTAKE CODES FOR STOVES WITH DREEFS CONTROL
The adhering to graph reveals the mistake codes that can be presented in the Oven/Selector window throughout certain oven malfunctions. Several of the mistake messages can be gotten rid of by carrying out the complying with actions:

Turn the selector handle to OFF
2.”Modify” the stove by turning the selector handle slightly to the left (counterclockwise). This might quit the blinking message/beeping as well as clear the home window.
For errors E1, E9, E11, E12 as well as E13, the power supply going to the even have to be turned off momentarily, as well as back on once again.
If a mistake remains presented when the selector button is OFF, and after attempting to get rid of the display screen, as received actions 2 and 3, shut off the power going to the stove, as well as refer to the chart below to aid you discover the trouble.

ERROR MESSAGE	ERROR CODE NOTES	DESCRIPTION OF PROBLEM
E1	C&E	Control board problem.
E2	G&K	Cook or Clean mode runaway (temp >635 °F) Clean mode runaway (clean temp +32 °F).
E3	A&H	Open oven temperature sensor (>5000 Ω).
E4	A&H	Shorted oven temperature sensor (<5000 Ω).
E5	K&D	Control board too cold, too hot, or defective.
E6	C&J	Control board problem.
E7	A&I	Illegal temperature display. Turn off oven and try again.
E8	A&D	Control board problem.
E9	A&E	Latch switch problem.
E10	B&D	Control board problem.
E11	A&F	CT oven – latch switch problem
E12	A&E	CT ovens – latch switch problem
E13	A&C	CT ovens – latch frozen or no power to latch motor. CMT ovens – control board not converted (refer to page 3-7 for conversion data).
E14	A&E	Latch switch problem.
E15	B&D	Control board problem.

ERROR CODE NOTES	DESCRIPTION OF PROBLEM
A	Turns heat off on the failed oven only; microwave not affected.
B	Turns all heat off; microwave not affected.
C	Disables the CLEAN mode in both ovens; allows COOK and microwave.
D	Error will remain in the display until oven is repaired and powered back up. No error tones.
E	Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN.
F	Tweaking clears to “—“ for retry.
G	Clears when the oven temperature is less then the runaway temperature with the selector switch off.
H	Can be cancelled by tweaking if a good sensor is detected.
I	Cleared with a mode change.
J	Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door.
K	Turns heat and microwave off.
L	If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message.