APPLIANCE REPAIR NEW YORK

Refrigerator Repair

Oven Repair

Dryer Repair

Washer Repair

MORE APPLIANCES

THERMADOR Error Code E7
Professional Ranges Models: PDR30/36/48…PRG30/36/48

ERROR CODE	DESCRIPTION	RESOLUTION
CODE E7	Turns heat off on failed oven only, micro not affected. Cleared with a mode change.	Illegal temp display turn off and retry

The control continually checks system specifications for control as well as oven failures and reports a mistake code when a system trouble is discovered. The control utilizes the ovens blue “on light” and oven “home heating light” to report a found mistake code. The control will certainly continue to flash the lights in the proper sequence as long as the fault exists.

Discovery of a fault does not impede the ability of the control to remain to work if the fault is not critical for the intended operation. For example: If the variety door lock is defective, the range will continue to prepare considering that the fault would only stop the array from self-cleaning.

HOW TO TRANSLATE CODES
When a mistake happens, the control will certainly blink the blue oven “on light” and also the Blue “heating light” sequentially to indicate the fault. The fault codes have two numbers, these numbers are translated by the number of times the lights blink. The stove “on light” will flash showing the initial number, and the “home heating light” will certainly flash suggesting the 2nd number.

EXAMPLE:
Error E9 is … No Air conditioning Followers. The code is 43. The stove “on light” will blink four times, then the “home heating light” will certainly flash 3 times, after that time out. The series will then duplicate as long as the mistake is present.

ERROR CODES FOR OVENS WITH DREEFS CONTROL
The following graph reveals the mistake codes that can be shown in the Oven/Selector home window during certain stove malfunctions. A few of the mistake messages can be gotten rid of by doing the following actions:

Turn the selector handle to OFF
2.”Modify” the stove by transforming the selector knob somewhat to the left (counterclockwise). This may quit the blinking message/beeping and clear the home window.
For errors E1, E9, E11, E12 as well as E13, the power supply mosting likely to the even should be shut off momentarily, and back on again.
If an error stays displayed when the selector button is OFF, and also after trying to remove the screen, as shown in steps 2 and also 3, switch off the power mosting likely to the oven, as well as refer to the graph listed below to help you locate the problem.

ERROR MESSAGE	ERROR CODE NOTES	DESCRIPTION OF PROBLEM
E1	C&E	Control board problem.
E2	G&K	Cook or Clean mode runaway (temp >635 °F) Clean mode runaway (clean temp +32 °F).
E3	A&H	Open oven temperature sensor (>5000 Ω).
E4	A&H	Shorted oven temperature sensor (<5000 Ω).
E5	K&D	Control board too cold, too hot, or defective.
E6	C&J	Control board problem.
E7	A&I	Illegal temperature display. Turn off oven and try again.
E8	A&D	Control board problem.
E9	A&E	Latch switch problem.
E10	B&D	Control board problem.
E11	A&F	CT oven – latch switch problem
E12	A&E	CT ovens – latch switch problem
E13	A&C	CT ovens – latch frozen or no power to latch motor. CMT ovens – control board not converted (refer to page 3-7 for conversion data).
E14	A&E	Latch switch problem.
E15	B&D	Control board problem.

ERROR CODE NOTES	DESCRIPTION OF PROBLEM
A	Turns heat off on the failed oven only; microwave not affected.
B	Turns all heat off; microwave not affected.
C	Disables the CLEAN mode in both ovens; allows COOK and microwave.
D	Error will remain in the display until oven is repaired and powered back up. No error tones.
E	Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN.
F	Tweaking clears to “—“ for retry.
G	Clears when the oven temperature is less then the runaway temperature with the selector switch off.
H	Can be cancelled by tweaking if a good sensor is detected.
I	Cleared with a mode change.
J	Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door.
K	Turns heat and microwave off.
L	If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message.