APPLIANCE REPAIR NEW YORK

Refrigerator Repair

Oven Repair

Dryer Repair

Washer Repair

MORE APPLIANCES

THERMADOR Error Code E8
Professional Ranges Models: PDR30/36/48…PRG30/36/48

ERROR CODE	DESCRIPTION	RESOLUTION
CODE E8	Turns heat off on failed oven only, micro not affected. Error will remain in display until repaired and powered up. No error tones.Turns heat off on failed oven only, micro not affected.	Repair the electronic range control (also called clock or ERC)

The control continuously checks system parameters for control as well as oven failures and reports a mistake code when a system problem is spotted. The control makes use of the ovens blue “on light” as well as oven “home heating light” to report a spotted mistake code. The control will continue to blink the lights in the ideal series as long as the fault exists.

Detection of a fault does not hinder the capacity of the control to continue to function if the fault is not crucial for the designated operation. For example: If the variety door lock is inoperative, the variety will remain to prepare because the mistake would only protect against the range from self-cleaning.

HOW TO INTERPRET CODES
When a mistake takes place, the control will flash the blue stove “on light” as well as heaven “heating light” sequentially to suggest the mistake. The fault codes have 2 numbers, these numbers are interpreted by the variety of times the lights flash. The stove “on light” will certainly flash indicating the first number, and the “heating light” will blink showing the 2nd number.

INSTANCE:
Error E9 is … No Cooling Fans. The code is 43. The oven “on light” will certainly blink four times, then the “home heating light” will flash 3 times, after that pause. The sequence will certainly then duplicate as long as the mistake exists.

MISTAKE CODES FOR STOVES WITH DREEFS CONTROL
The following chart reveals the mistake codes that can be displayed in the Oven/Selector home window during specific stove breakdowns. Some of the error messages can be gotten rid of by performing the adhering to actions:

Transform the selector knob to OFF
2.”Modify” the stove by transforming the selector knob slightly to the left (counterclockwise). This might quit the blinking message/beeping and also clear the window.
For mistakes E1, E9, E11, E12 as well as E13, the power supply going to the also need to be turned off briefly, and also back on again.
If a mistake continues to be presented when the selector button is OFF, and after attempting to clear the display, as received steps 2 and also 3, turn off the power mosting likely to the stove, and describe the graph below to assist you discover the trouble.

ERROR MESSAGE	ERROR CODE NOTES	DESCRIPTION OF PROBLEM
E1	C&E	Control board problem.
E2	G&K	Cook or Clean mode runaway (temp >635 °F) Clean mode runaway (clean temp +32 °F).
E3	A&H	Open oven temperature sensor (>5000 Ω).
E4	A&H	Shorted oven temperature sensor (<5000 Ω).
E5	K&D	Control board too cold, too hot, or defective.
E6	C&J	Control board problem.
E7	A&I	Illegal temperature display. Turn off oven and try again.
E8	A&D	Control board problem.
E9	A&E	Latch switch problem.
E10	B&D	Control board problem.
E11	A&F	CT oven – latch switch problem
E12	A&E	CT ovens – latch switch problem
E13	A&C	CT ovens – latch frozen or no power to latch motor. CMT ovens – control board not converted (refer to page 3-7 for conversion data).
E14	A&E	Latch switch problem.
E15	B&D	Control board problem.

ERROR CODE NOTES	DESCRIPTION OF PROBLEM
A	Turns heat off on the failed oven only; microwave not affected.
B	Turns all heat off; microwave not affected.
C	Disables the CLEAN mode in both ovens; allows COOK and microwave.
D	Error will remain in the display until oven is repaired and powered back up. No error tones.
E	Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN.
F	Tweaking clears to “—“ for retry.
G	Clears when the oven temperature is less then the runaway temperature with the selector switch off.
H	Can be cancelled by tweaking if a good sensor is detected.
I	Cleared with a mode change.
J	Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door.
K	Turns heat and microwave off.
L	If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message.