APPLIANCE REPAIR NEW YORK

Refrigerator Repair

Oven Repair

Dryer Repair

Washer Repair

MORE APPLIANCES

THERMADOR Error Code E9
Professional Ranges Models: PDR30/36/48…PRG30/36/48

ERROR CODE	DESCRIPTION	RESOLUTION
CODE E9	Turn the clock selector knob to OFF Adjust the oven control by turning the clock selector knob slightly to the left (counter clockwise). This may stop the flashing message/beeping and clear the display window.	Latch switch problems

The control continuously checks system parameters for control and also stove failings and also reports a fault code when a system problem is spotted. The control utilizes the ovens blue “on light” as well as oven “home heating light” to report a detected mistake code. The control will remain to blink the lights in the suitable series as long as the fault exists.

Discovery of a mistake does not hinder the ability of the control to continue to operate if the mistake is not crucial for the intended operation. For example: If the variety door lock is inoperative, the range will certainly continue to cook given that the mistake would only prevent the variety from self-cleaning.

HOW TO TRANSLATE CODES
When a fault happens, the control will blink heaven oven “on light” and also heaven “home heating light” sequentially to show the mistake. The mistake codes have 2 numbers, these numbers are translated by the number of times the lights blink. The stove “on light” will flash indicating the very first number, and the “home heating light” will certainly blink suggesting the 2nd number.

EXAMPLE:
Mistake E9 is … No Cooling Followers. The code is 43. The stove “on light” will certainly flash four times, after that the “heating light” will flash 3 times, after that pause. The sequence will certainly after that repeat as long as the fault is present.

MISTAKE CODES FOR OVENS WITH DREEFS CONTROL
The complying with chart reveals the error codes that can be displayed in the Oven/Selector window throughout certain oven breakdowns. A few of the error messages can be gotten rid of by performing the following steps:

Transform the selector knob to OFF
2.”Tweak” the oven by transforming the selector knob slightly to the left (counterclockwise). This may quit the blinking message/beeping and also clear the home window.
For errors E1, E9, E11, E12 as well as E13, the power supply going to the also need to be turned off for a little while, and also back on once again.
If a mistake stays displayed when the selector button is OFF, and also after attempting to remove the display, as shown in actions 2 and also 3, shut off the power mosting likely to the stove, as well as describe the chart listed below to assist you locate the trouble.

ERROR MESSAGE	ERROR CODE NOTES	DESCRIPTION OF PROBLEM
E1	C&E	Control board problem.
E2	G&K	Cook or Clean mode runaway (temp >635 °F) Clean mode runaway (clean temp +32 °F).
E3	A&H	Open oven temperature sensor (>5000 Ω).
E4	A&H	Shorted oven temperature sensor (<5000 Ω).
E5	K&D	Control board too cold, too hot, or defective.
E6	C&J	Control board problem.
E7	A&I	Illegal temperature display. Turn off oven and try again.
E8	A&D	Control board problem.
E9	A&E	Latch switch problem.
E10	B&D	Control board problem.
E11	A&F	CT oven – latch switch problem
E12	A&E	CT ovens – latch switch problem
E13	A&C	CT ovens – latch frozen or no power to latch motor. CMT ovens – control board not converted (refer to page 3-7 for conversion data).
E14	A&E	Latch switch problem.
E15	B&D	Control board problem.

ERROR CODE NOTES	DESCRIPTION OF PROBLEM
A	Turns heat off on the failed oven only; microwave not affected.
B	Turns all heat off; microwave not affected.
C	Disables the CLEAN mode in both ovens; allows COOK and microwave.
D	Error will remain in the display until oven is repaired and powered back up. No error tones.
E	Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN.
F	Tweaking clears to “—“ for retry.
G	Clears when the oven temperature is less then the runaway temperature with the selector switch off.
H	Can be cancelled by tweaking if a good sensor is detected.
I	Cleared with a mode change.
J	Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door.
K	Turns heat and microwave off.
L	If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message.