APPLIANCE REPAIR NEW YORK

Refrigerator Repair

Oven Repair

Dryer Repair

Washer Repair

MORE APPLIANCES

THERMADOR Error Code F0
Professional Ranges Models: PDR30/36/48…PRG30/36/48

ERROR CODE	DESCRIPTION	RESOLUTION
CODE F0	Internal logic failure; cancel key supervision. Sounds alarm and resets to non-cook mode	Repair the electronic range control (also called clock or ERC)

The control constantly keeps an eye on system specifications for control as well as oven failings as well as reports a mistake code when a system trouble is spotted. The control uses the ovens blue “on light” and oven “heating light” to report an identified fault code. The control will continue to blink the lights in the proper sequence as long as the mistake exists.

Discovery of a fault does not hinder the ability of the control to remain to work if the fault is not crucial for the intended procedure. As an example: If the array door latch is inoperative, the variety will certainly remain to cook since the mistake would just avoid the variety from self-cleaning.

HOW TO TRANSLATE CODES
When a mistake takes place, the control will certainly flash heaven stove “on light” and also the Blue “heating light” sequentially to indicate the fault. The fault codes have 2 numbers, these numbers are translated by the number of times the lights blink. The oven “on light” will flash suggesting the very first number, and the “heating light” will flash suggesting the 2nd number.

INSTANCE:
Mistake E9 is … No Air conditioning Fans. The code is 43. The oven “on light” will certainly flash 4 times, then the “home heating light” will certainly blink three times, after that pause. The sequence will after that duplicate as long as the fault exists.

MISTAKE CODES FOR STOVES WITH DREEFS CONTROL
The complying with chart reveals the mistake codes that can be shown in the Oven/Selector window throughout certain stove breakdowns. Some of the error messages can be cleared by executing the following actions:

Transform the selector knob to OFF
2.”Tweak” the oven by turning the selector handle somewhat to the left (counterclockwise). This may stop the flashing message/beeping and clear the window.
For errors E1, E9, E11, E12 and also E13, the power supply mosting likely to the even must be shut off momentarily, and also back on once again.
If an error remains shown when the selector button is OFF, as well as after trying to get rid of the display, as received actions 2 and 3, turn off the power going to the stove, and refer to the chart listed below to assist you find the trouble.

ERROR CODE	NOTE	CHECK REPAIR
F0	Internal logic failure; cancel key supervision. Sounds alarm and resets to non-cook mode	Replace the electronic range control (also called clock or ERC)
F1	Internal logic failure (monitoring function). Sounds alarm and inhibits cook modes	Replace the electronic range control (also called clock or ERC)
F2	Temperature runaway detected (Bake/Broil: 600 – 700 F; Clean: 930 – 1000 degrees F). Sounds alarm and resets to non-cook mode. Check relay board for stuck contacts. Check oven temperature sensor for normal room temperature resistance (1085-1097 ohms at 75 degrees F). Check sensor wiring connectors for a loose or high resistance connection. Check electronic range control (also called clock or ERC) functions	Replace relay board if necessary. Replace oven temperature sensor if other components check normal. If failure repeats, replace electronic range control (also called clock or ERC)
F3	Open circuit detected; oven temperature sensor. Check sensor for normal room temperature resistance (1085-1097 ohms at 75 degrees F). Check wires and connections between electronic range control (also called clock or ERC) and oven temperature sensor	Replace sensor if other components check normal. Replace electronic range control (also called clock or ERC) if fail code reoccurs
F4	Short circuit detected; oven temperature sensor. Check sensor for normal room temperature resistance (1085-1097 ohms at 75 degrees F). Check wires between electronic range control (also called clock or ERC) and sensor.	Replace sensor if other components check normal. Replace electronic range control (also called clock or ERC) if fail code reoccurs
F7	Function key shorted for over 16 seconds. Check for something pressing a key or preventing normal release of the key	Replace electronic range control (also called clock or ERC) if other components check normal
F8	Internal logic failure; calibration. Alarm sounds and resets to non-cook mode. Check oven temperature sensor for normal room temperature resistance (1085-1097 ohms at 75 F). Check wires and connections between electronic range control (also called clock or ERC) and oven temperature sensor	Replace electronic range control (also called clock or ERC) and oven temperature sensor if other components check normal
F9	Internal logic ailure; door latch supervision. Alarm sounds and resets to non-cook mode. If door is locked due to clean temperatures, disconnect power until door can be unlocked	Replace the electronic range control (also called clock or ERC)
Fd	Bake & Broil relay drives active simultaneously. Check relay board for damage: trace E6 to K2 & K3, and burned contacts K3 & K3	Replace electronic range control (also called clock or ERC). Replace relay board if necessary
Blank Display	No power to lectronic range control (also called clock or ERC). Check oven light and cooktop dial lights (powered by L2 & L1, respectively). Check relay board transformer primary, E1 to E2 (140 ohms typical). If the transformer internal fuse is still OK, check output voltages, pins 9 – 8 (3.2 v.a.c.) and 7 – 6 (21 v.a.c.). Check clock functions after replacing relay board	If relay board transformer open (E1 to E2), replace relay board. If still no clock functions replace electronic range control (also called clock or ERC)

ERROR CODE	NOTES
A	Turns heat off on the failed oven only; microwave not affected.
B	Turns all heat off; microwave not affected.
C	Disables the CLEAN mode in both ovens; allows COOK and microwave.
D	Error will remain in the display until oven is repaired and powered back up. No error tones.
E	Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN.
F	Tweaking clears to “—“ for retry.
G	Clears when the oven temperature is less then the runaway temperature with the selector switch off.
H	Can be cancelled by tweaking if a good sensor is detected.
I	Cleared with a mode change.
J	Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door.
K	Turns heat and microwave off.
L	If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message.